If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/iio/adc/fsl-imx25-gcq.ko | grep alias
$
After this patch:
$ modinfo drivers/iio/adc/fsl-imx25-gcq.ko | grep alias
alias: of:N*T*Cfsl,imx25-gcqC*
alias: of:N*T*Cfsl,imx25-gcq
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writes into limit attributes can overflow due to multplications and
additions with unbound input values. Writing into fan limit attributes
can result in a crash with a division by zero if very large values are
written and the fan divider is larger than 1.
The MIPS based MT7621 shares the same XHCI core as the newer generation of
ARM based SoCs. The driver works out of the box and we only need to make it
buildable in Kconfig.
The vbus-present bit in the power status register also gets set to 1
when a usb-host cable (id-pin shorted to ground) is plugged in and a 5v
boost converter is supplying 5v to the otg usb bus.
This causes a "disconnect or unknown or ID event" warning in dmesg as
well as the extcon device to report the last detected charger cable
type as being connected even though none is connected.
This commit switches to checking the vbus-valid bit instead, which is
only 1 when both vbus is present and the vbus-path is enabled in the
vbus-path control register (the vbus-path gets disabled when a usb-host
cable is detected, to avoid the pmic drawing power from the 5v boost
converter).
Whenever the igb driver detects the result of a read operation returns
a value composed only by F's (like 0xFFFFFFFF), it will detach the
net_device, clear the hw_addr pointer and warn to the user that adapter's
link is lost - those steps happen on igb_rd32().
In case a PCI error happens on Power architecture, there's a recovery
mechanism called EEH, that will reset the PCI slot and call driver's
handlers to reset the adapter and network functionality as well.
We observed that once hw_addr is NULL after the error is detected on
igb_rd32(), it's never assigned back, so in the process of resetting
the network functionality we got a NULL pointer dereference in both
igb_configure_tx_ring() and igb_configure_rx_ring(). In order to avoid
such bug, this patch re-assigns the hw_addr value in the slot_reset
handler.
Reported-by: Anthony H Thai <ahthai@us.ibm.com> Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com> Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On chiliSOM TPS65217 nWAKEUP pin is connected to AM335x internal RTC
EXT_WAKEUP input. In RTC-only state TPS65217 is notifying about power on
events (such as power buton presses) by setting nWAKEUP output
low. After that it waits 5s for proper device boot. Currently it doesn't
happen, as the processor doesn't listen for such events. Consequently
TPS65217 changes state from SLEEP (RTC-only state) to OFF.
Enable EXT_WAKEUP input of AM335x's RTC, so the processor can properly
detect power on events and recover immediately from RTC-only states,
without powering off RTC and losing time.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set CID slot to 0xffff to indicate empty.
Check if connection already exists in conn_table before binding.
Check if endpoint already NULL before putting back CID.
Break ep->conn link in free_ep to ignore completions after freeing.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a typo inside the pinmux setup code. The function is really
called utif and not util. This was recently discovered when people were
trying to make the UTIF interface work.
When clearing the .bss section in kernel_entry we do so using LONG_S
instructions, and branch whilst the current write address doesn't equal
the end of the .bss section minus the size of a long integer. The .bss
section always begins at a long-aligned address and we always increment
the write pointer by the size of a long integer - we therefore rely upon
the .bss section ending at a long-aligned address. If this is not the
case then the long-aligned write address can never be equal to the
non-long-aligned end address & we will continue to increment past the
end of the .bss section, attempting to zero the rest of memory.
Despite this requirement that .bss end at a long-aligned address we pass
0 as the end alignment requirement to the BSS_SECTION macro and thus
don't guarantee any particular alignment, allowing us to hit the error
condition described above.
Fix this by instead passing 8 bytes as the end alignment argument to
the BSS_SECTION macro, ensuring that the end of the .bss section is
always at least long-aligned.
Use recently added R-Car Gen 2 fallback binding for msiof nodes in
DT for r8a7790 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7790 and the
fallback binding for R-Car Gen 2.
When application sends an RDS RDMA composite message consist of
RDMA transfer to be followed up by non RDMA payload, it expect to
be notified *only* when the full message gets delivered. RDS RDMA
notification doesn't behave this way though.
Thanks to Venkat for debug and root casuing the issue
where only first part of the message(RDMA) was
successfully delivered but remainder payload delivery failed.
In that case, application should not be notified with
a false positive of message delivery success.
Fix this case by making sure the user gets notified only after
the full message delivery.
Add CPU operating points for Exynos4412 Prime (it supports
additional 1704MHz & 1600MHz OPPs and 1500MHz OPP is just
a regular non-turbo OPP on this SoC). Also update relevant
cooling maps to account for new OPPs.
ODROID-X2/U2/U3 boards use Exynos4412 Prime SoC version so
update their board files accordingly.
Based on Hardkernel's kernel for ODROID-X2/U2/U3 boards.
Cc: Doug Anderson <dianders@chromium.org> Cc: Andreas Faerber <afaerber@suse.de> Cc: Thomas Abraham <thomas.ab@samsung.com> Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de> Cc: Ben Gamari <ben@smart-cactus.org> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do the overlay frontbuffer tracking properly so that it matches
the state of the overlay on/off/continue requests.
One slight problem is that intel_frontbuffer_flip_complete()
may get delayed by an arbitrarily liong time due to the fact that
the overlay code likes to bail out when a signal occurs. So the
flip may not get completed until the ioctl is restarted. But fixing
that would require bigger surgery, so I decided to ignore it for now.
'clk' is copied to a userland with padding byte(s) after 'vclk_post_div'
field unitialized, leaking data from the stack. Fix this ensuring all of
'clk' is initialized to zero.
cxl keeps a driver use count, which is used with the hash memory model
on p8 to know when to upgrade local TLBIs to global and to trigger
callbacks to manage the MMU for PSL8.
If a process opens a context and closes without attaching or fails the
attachment, the driver use count is never decremented. As a
consequence, TLB invalidations remain global, even if there are no
active cxl contexts.
We should increment the driver use count when the process is attaching
to the cxl adapter, and not on open. It's not needed before the
adapter starts using the context and the use count is decremented on
the detach path, so it makes more sense.
It affects only the user api. The kernel api is already doing The
Right Thing.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Cc: stable@vger.kernel.org # v4.2+ Fixes: 7bb5d91a4dda ("cxl: Rework context lifetimes") Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[ajd: backport to stable v4.9 tree] Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARN_ON_ONCE(pi_test_sn(&vmx->pi_desc)) in kvm_vcpu_trigger_posted_interrupt()
intends to detect the violation of invariant that VT-d PI notification
event is not suppressed when vcpu is in the guest mode. Because the
two checks for the target vcpu mode and the target suppress field
cannot be performed atomically, the target vcpu mode may change in
between. If that does happen, WARN_ON_ONCE() here may raise false
alarms.
As the previous patch fixed the real invariant breaker, remove this
WARN_ON_ONCE() to avoid false alarms, and document the allowed cases
instead.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com> Reported-by: "Ramamurthy, Venkatesh" <venkatesh.ramamurthy@intel.com> Reported-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Fixes: 28b835d60fcc ("KVM: Update Posted-Interrupts Descriptor when vCPU is preempted") Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In kvm_vcpu_trigger_posted_interrupt() and pi_pre_block(), KVM
assumes that PI notification events should not be suppressed when the
target vCPU is not blocked.
vmx_update_pi_irte() sets the SN field before changing an interrupt
from posting to remapping, but it does not check the vCPU mode.
Therefore, the change of SN field may break above the assumption.
Besides, I don't see reasons to suppress notification events here, so
remove the changes of SN field to avoid race condition.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com> Reported-by: "Ramamurthy, Venkatesh" <venkatesh.ramamurthy@intel.com> Reported-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Fixes: 28b835d60fcc ("KVM: Update Posted-Interrupts Descriptor when vCPU is preempted") Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch to rhashtables (commit 88ffbf3e03) broke the debugfs glock
dump (/sys/kernel/debug/gfs2/<device>/glocks) for dumps bigger than a
single buffer: the right function for restarting an rhashtable iteration
from the beginning of the hash table is rhashtable_walk_enter;
rhashtable_walk_stop + rhashtable_walk_start will just resume from the
current position.
The upstream commit doesn't directly apply to 4.9.y because 4.9.y
doesn't have the following mainline commits:
On x86, userspace can use the ptrace() or rt_sigreturn() system calls to
set a task's extended state (xstate) or "FPU" registers. ptrace() can
set them for another task using the PTRACE_SETREGSET request with
NT_X86_XSTATE, while rt_sigreturn() can set them for the current task.
In either case, registers can be set to any value, but the kernel
assumes that the XSAVE area itself remains valid in the sense that the
CPU can restore it.
However, in the case where the kernel is using the uncompacted xstate
format (which it does whenever the XSAVES instruction is unavailable),
it was possible for userspace to set the xcomp_bv field in the
xstate_header to an arbitrary value. However, all bits in that field
are reserved in the uncompacted case, so when switching to a task with
nonzero xcomp_bv, the XRSTOR instruction failed with a #GP fault. This
caused the WARN_ON_FPU(err) in copy_kernel_to_xregs() to be hit. In
addition, since the error is otherwise ignored, the FPU registers from
the task previously executing on the CPU were leaked.
Fix the bug by checking that the user-supplied value of xcomp_bv is 0 in
the uncompacted case, and returning an error otherwise.
The reason for validating xcomp_bv rather than simply overwriting it
with 0 is that we want userspace to see an error if it (incorrectly)
provides an XSAVE area in compacted format rather than in uncompacted
format.
Note that as before, in case of error we clear the task's FPU state.
This is perhaps non-ideal, especially for PTRACE_SETREGSET; it might be
better to return an error before changing anything. But it seems the
"clear on error" behavior is fine for now, and it's a little tricky to
do otherwise because it would mean we couldn't simply copy the full
userspace state into kernel memory in one __copy_from_user().
This bug was found by syzkaller, which hit the above-mentioned
WARN_ON_FPU():
Here is a C reproducer. The expected behavior is that the program spin
forever with no output. However, on a buggy kernel running on a
processor with the "xsave" feature but without the "xsaves" feature
(e.g. Sandy Bridge through Broadwell for Intel), within a second or two
the program reports that the xmm registers were corrupted, i.e. were not
restored correctly. With CONFIG_X86_DEBUG_FPU=y it also hits the above
kernel warning.
Note: the program only tests for the bug using the ptrace() system call.
The bug can also be reproduced using the rt_sigreturn() system call, but
only when called from a 32-bit program, since for 64-bit programs the
kernel restores the FPU state from the signal frame by doing XRSTOR
directly from userspace memory (with proper error checking).
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Eric Biggers <ebiggers3@gmail.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Kevin Hao <haokexin@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Halcrow <mhalcrow@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Yu-cheng Yu <yu-cheng.yu@intel.com> Cc: kernel-hardening@lists.openwall.com Fixes: 0b29643a5843 ("x86/xsaves: Change compacted format xsave area header") Link: http://lkml.kernel.org/r/20170922174156.16780-2-ebiggers3@gmail.com Link: http://lkml.kernel.org/r/20170923130016.21448-25-mingo@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b2d0dbac489 ("x86/mm/pkeys: Pass VMA down in to fault signal
generation code") passes down a vma pointer to the error path, but that is
done once the mmap_sem is released when calling mm_fault_error() from
__do_page_fault().
This is dangerous as the vma structure is no more safe to be used once the
mmap_sem has been released. As only the protection key value is required in
the error processing, we could just pass down this value.
Fix it by passing a pointer to a protection key value down to the fault
signal generation code. The use of a pointer allows to keep the check
generating a warning message in fill_sig_info_pkey() when the vma was not
known. If the pointer is valid, the protection value can be accessed by
deferencing the pointer.
[ tglx: Made *pkey u32 as that's the type which is passed in siginfo ]
Fixes: 7b2d0dbac489 ("x86/mm/pkeys: Pass VMA down in to fault signal generation code") Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Cc: Dave Hansen <dave.hansen@linux.intel.com> Link: http://lkml.kernel.org/r/1504513935-12742-1-git-send-email-ldufour@linux.vnet.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`btrfs sub set-default` succeeds to set an ID which isn't corresponding to any
fs/file tree. If such the bad ID is set to a filesystem, we can't mount this
filesystem without specifying `subvol` or `subvolid` mount options.
Fixes: 6ef5ed0d386b ("Btrfs: add ioctl and incompat flag to set the default mount subvol") Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com> Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
btrfs_cmp_data_prepare() (almost) always returns 0 i.e. ignoring errors
from gather_extent_pages(). While the pages are freed by
btrfs_cmp_data_free(), cmp->num_pages still has > 0. Then,
btrfs_extent_same() try to access the already freed pages causing faults
(or violates PageLocked assertion).
This patch just return the error as is so that the caller stop the process.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Fixes: f441460202cb ("btrfs: fix deadlock with extent-same and readpage") Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__del_reloc_root should be called before freeing up reloc_root->node.
If not, calling __del_reloc_root() dereference reloc_root->node, causing
the system BUG.
Fixes: 6bdf131fac23 ("Btrfs: don't leak reloc root nodes on error") Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_override implementation is susceptible to a race condition when
different threads are reading vs. storing a different driver override. Add
locking to avoid the race condition.
This is in close analogy to commit 6265539776a0 ("driver core: platform:
fix race condition with driver_override") from Adrian Salido.
All manipulations of the gem_object list need to be protected by
the list mutex, as GEM objects can be created and freed in parallel.
This fixes a kernel memory corruption.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently only the blocksize is checked, but we should really be calling
bdev_dax_supported() which also tests to make sure we can get a
struct dax_device and that the dax_direct_access() path is working.
This is the same check that we do for the "-o dax" mount option in
xfs_fs_fill_super().
This does not fix the race issues that caused the XFS DAX inode option to
be disabled, so that option will still be disabled. If/when we re-enable
it, though, I think we will want this issue to have been fixed. I also do
think that we want to fix this in stable kernels.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If L1 does not specify the "use TPR shadow" VM-execution control in
vmcs12, then L0 must specify the "CR8-load exiting" and "CR8-store
exiting" VM-execution controls in vmcs02. Failure to do so will give
the L2 VM unrestricted read/write access to the hardware CR8.
This fixes CVE-2017-12154.
Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of the guest_irq argument to vmx_update_pi_irte() is
ultimately coming from a KVM_IRQFD API call. Do not BUG() in
vmx_update_pi_irte() if the value is out-of bounds. (Especially,
since KVM as a whole seems to hang after that.)
Instead, print a message only once if we find that we don't have a
route for a certain IRQ (which can be out-of-bounds or within the
array).
This happened when the host hit a page fault, and delivered it as in an
async page fault, while the guest was in an RCU read-side critical
section. The guest then tries to reschedule in kvm_async_pf_task_wait(),
but rcu_preempt_note_context_switch() would treat the reschedule as a
sleep in RCU read-side critical section, which is not allowed (even in
preemptible RCU). Thus the WARN.
To cure this, make kvm_async_pf_task_wait() go to the halt path if the
PF happens in a RCU read-side critical section.
Reported-by: Sasha Levin <levinsasha928@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Boqun Feng <boqun.feng@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The simplify part: do not touch pi_desc.nv, we can set it when the
VCPU is first created. Likewise, pi_desc.sn is only handled by
vmx_vcpu_pi_load, do not touch it in __pi_post_block.
The fix part: do not check kvm_arch_has_assigned_device, instead
check the SN bit to figure out whether vmx_vcpu_pi_put ran before.
This matches what the previous patch did in pi_post_block.
In some cases, for example involving hot-unplug of assigned
devices, pi_post_block can forget to remove the vCPU from the
blocked_vcpu_list. When this happens, the next call to
pi_pre_block corrupts the list.
Fix this in two ways. First, check vcpu->pre_pcpu in pi_pre_block
and WARN instead of adding the element twice in the list. Second,
always do the list removal in pi_post_block if vcpu->pre_pcpu is
set (not -1).
The new code keeps interrupts disabled for the whole duration of
pi_pre_block/pi_post_block. This is not strictly necessary, but
easier to follow. For the same reason, PI.ON is checked only
after the cmpxchg, and to handle it we just call the post-block
code. This removes duplication of the list removal code.
We currently route pte translation faults via do_page_fault, which elides
the address check against TASK_SIZE before invoking the mm fault handling
code. However, this can cause issues with the path walking code in
conjunction with our word-at-a-time implementation because
load_unaligned_zeropad can end up faulting in kernel space if it reads
across a page boundary and runs into a page fault (e.g. by attempting to
read from a guard region).
In the case of such a fault, load_unaligned_zeropad has registered a
fixup to shift the valid data and pad with zeroes, however the abort is
reported as a level 3 translation fault and we dispatch it straight to
do_page_fault, despite it being a kernel address. This results in calling
a sleeping function from atomic context:
When the kernel is entered at EL2 on an ARMv8.0 system, we construct
the EL1 pstate and make sure this uses the the EL1 stack pointer
(we perform an exception return to EL1h).
But if the kernel is either entered at EL1 or stays at EL2 (because
we're on a VHE-capable system), we fail to set SPsel, and use whatever
stack selection the higher exception level has choosen for us.
Let's not take any chance, and make sure that SPsel is set to one
before we decide the mode we're going to run in.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Chris explains, get_seccomp_filter() and put_seccomp_filter() can end
up using different filters. Once we drop ->siglock it is possible for
task->seccomp.filter to have been replaced by SECCOMP_FILTER_FLAG_TSYNC.
Fixes: f8e529ed941b ("seccomp, ptrace: add support for dumping seccomp filters") Reported-by: Chris Salls <chrissalls5@gmail.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[tycho: add __get_seccomp_filter vs. open coding refcount_inc()] Signed-off-by: Tycho Andersen <tycho@docker.com>
[kees: tweak commit log] Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2.26 release of glibc changed how siginfo_t is defined, and the earlier
work-around to using the kernel definition are no longer needed. The old
way needs to stay around for a while, though.
If a listen create fails, then the server tid (stid) is incorrectly left
in the stid idr table, which can cause a touch-after-free if the stid
is looked up and the already freed endpoint is touched. So make sure
and remove it in the error path.
nl80211_set_rekey_data() does not check if the required attributes
NL80211_REKEY_DATA_{REPLAY_CTR,KEK,KCK} are present when processing
NL80211_CMD_SET_REKEY_OFFLOAD request. This request can be issued by
users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attributes presence.
This patch is based on the patch by bo Zhang.
This fixes CVE-2017-12153.
References: https://bugzilla.redhat.com/show_bug.cgi?id=1491046 Fixes: e5497d766ad ("cfg80211/nl80211: support GTK rekey offload") Reported-by: bo Zhang <zhangbo5891001@gmail.com> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In generic_file_llseek_size, return -ENXIO for negative offsets as well
as offsets beyond EOF. This affects filesystems which don't implement
SEEK_HOLE / SEEK_DATA internally, possibly because they don't support
holes.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As long as signing is supported (ie not a guest user connection) and
connection is SMB3 or SMB3.02, then validate negotiate (protect
against man in the middle downgrade attacks). We had been doing this
only when signing was required, not when signing was just enabled,
but this more closely matches recommended SMB3 behavior and is
better security. Suggested by Metze.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Jeremy Allison <jra@samba.org> Acked-by: Stefan Metzmacher <metze@samba.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can be confusing if user ends up authenticated as guest but they
requested signing (server will return error validating signed packets)
so add log message for this.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samba rejects SMB3.1.1 dialect (vers=3.1.1) negotiate requests from
the kernel client due to the two byte pad at the end of the negotiate
contexts.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device_pm_check_callbacks() function doesn't check legacy
->suspend and ->resume callback pointers under the device's
bus type, class and driver, so in some cases it may set the
no_pm_callbacks flag for the device incorrectly and then the
callbacks may be skipped during system suspend/resume, which
shouldn't happen.
Fixes: aa8e54b55947 (PM / sleep: Go direct_complete if driver has no callbacks) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for the _SEGMENT_ENTRY_PROTECT bit in gup_huge_pmd() is the
wrong way around. It must not be set for write==1, and not be checked for
write==0. Fix this similar to how it was fixed for ptes long time ago in
commit 25591b070336 ("[S390] fix get_user_pages_fast").
One impact of this bug would be unnecessarily using the gup slow path for
write==0 on r/w mappings. A potentially more severe impact would be that
gup_huge_pmd() will succeed for write==1 on r/o mappings.
For DYNAMIC_FTRACE_WITH_REGS, we should be passing-in the original set
of registers in pt_regs, to capture the state _before_ ftrace_caller.
However, we are instead passing the stack pointer *after* allocating a
stack frame in ftrace_caller. Fix this by saving the proper value of r1
in pt_regs. Also, use SAVE_10GPRS() to simplify the code.
Fixes: 153086644fd1 ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cd63f3c ("powerpc/tm: Fix saving of TM SPRs in core dump")
added code to access TM SPRs in flush_tmregs_to_thread(). However
flush_tmregs_to_thread() does not check if TM feature is available on
CPU before trying to access TM SPRs in order to copy live state to
thread structures. flush_tmregs_to_thread() is indeed guarded by
CONFIG_PPC_TRANSACTIONAL_MEM but it might be the case that kernel
was compiled with CONFIG_PPC_TRANSACTIONAL_MEM enabled and ran on
a CPU without TM feature available, thus rendering the execution
of TM instructions that are treated by the CPU as illegal instructions.
The fix is just to add proper checking in flush_tmregs_to_thread()
if CPU has the TM feature before accessing any TM-specific resource,
returning immediately if TM is no available on the CPU. Adding
that checking in flush_tmregs_to_thread() instead of in places
where it is called, like in vsr_get() and vsr_set(), is better because
avoids the same problem cropping up elsewhere.
Fixes: cd63f3c ("powerpc/tm: Fix saving of TM SPRs in core dump") Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com> Reviewed-by: Cyril Bur <cyrilbur@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A reference to the parent device node is held by add_dt_node() for the
node to be added. If the call to dlpar_configure_connector() fails
add_dt_node() returns ENOENT and that reference is not freed.
Add a call to of_node_put(parent_dn) prior to bailing out after a
failed dlpar_configure_connector() call.
Fixes: 8d5ff320766f ("powerpc/pseries: Make dlpar_configure_connector parent node aware") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because keyctl_read_key() looks up the key with no permissions
requested, it may find a negatively instantiated key. If the key is
also possessed, we went ahead and called ->read() on the key. But the
key payload will actually contain the ->reject_error rather than the
normal payload. Thus, the kernel oopses trying to read the
user_key_payload from memory address (int)-ENOKEY = 0x00000000ffffff82.
Fortunately the payload data is stored inline, so it shouldn't be
possible to abuse this as an arbitrary memory read primitive...
Reproducer:
keyctl new_session
keyctl request2 user desc '' @s
keyctl read $(keyctl show | awk '/user: desc/ {print $1}')
Fixes: 61ea0c0ba904 ("KEYS: Skip key state checks when checking for possession") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is problematic because these "fake" keyrings won't have the right
permissions. In particular, the user who created them first will own
them and will have full access to them via the possessor permissions,
which can be used to compromise the security of a user's keys:
Fix it by marking user and user session keyrings with a flag
KEY_FLAG_UID_KEYRING. Then, when searching for a user or user session
keyring by name, skip all keyrings that don't have the flag set.
Fixes: 69664cf16af4 ("keys: don't generate user and user session keyrings unless they're accessed") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace can call keyctl_read() on a keyring to get the list of IDs of
keys in the keyring. But if the user-supplied buffer is too small, the
kernel would write the full list anyway --- which will corrupt whatever
userspace memory happened to be past the end of the buffer. Fix it by
only filling the space that is available.
Fixes: b2a4df200d57 ("KEYS: Expand the capacity of a keyring") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This started out as just replacing the use of crypto/rng with
get_random_bytes_wait, so that we wouldn't use bad randomness at boot
time. But, upon looking further, it appears that there were even deeper
underlying cryptographic problems, and that this seems to have been
committed with very little crypto review. So, I rewrote the whole thing,
trying to keep to the conventions introduced by the previous author, to
fix these cryptographic flaws.
It makes no sense to seed crypto/rng at boot time and then keep
using it like this, when in fact there's already get_random_bytes_wait,
which can ensure there's enough entropy and be a much more standard way
of generating keys. Since this sensitive material is being stored
untrusted, using ECB and no authentication is simply not okay at all. I
find it surprising and a bit horrifying that this code even made it past
basic crypto review, which perhaps points to some larger issues. This
patch moves from using AES-ECB to using AES-GCM. Since keys are uniquely
generated each time, we can set the nonce to zero. There was also a race
condition in which the same key would be reused at the same time in
different threads. A mutex fixes this issue now.
So, to summarize, this commit fixes the following vulnerabilities:
* Low entropy key generation, allowing an attacker to potentially
guess or predict keys.
* Unauthenticated encryption, allowing an attacker to modify the
cipher text in particular ways in order to manipulate the plaintext,
which is is even more frightening considering the next point.
* Use of ECB mode, allowing an attacker to trivially swap blocks or
compare identical plaintext blocks.
* Key re-use.
* Faulty memory zeroing.
[Note that in backporting this commit to 4.9, get_random_bytes_wait was
replaced with get_random_bytes, since 4.9 does not have the former
function. This might result in slightly worse entropy in key generation,
but common use cases of big_keys makes that likely not a huge deal. And,
this is the best we can do with this old kernel. Alas.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Eric Biggers <ebiggers3@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Kirill Marinushkin <k.marinushkin@gmail.com> Cc: security@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the change to use aligned buffers, the deallocation code path was
not updated correctly. The current code tries to free the aligned buffer
pointer and not the original buffer pointer as it is supposed to.
Thus, the code is updated to free the original buffer pointer and set
the aligned buffer pointer that is used throughout the code to NULL.
Fixes: 3cfc3b9721123 ("crypto: drbg - use aligned buffers") CC: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's caused by skb_shared_info at the end of sk_buff was overwritten by
ISCSI_KEVENT_IF_ERROR when parsing nlmsg info from skb in iscsi_if_rx.
During the loop if skb->len == nlh->nlmsg_len and both are sizeof(*nlh),
ev = nlmsg_data(nlh) will acutally get skb_shinfo(SKB) instead and set a
new value to skb_shinfo(SKB)->nr_frags by ev->type.
This patch is to fix it by checking nlh->nlmsg_len properly there to
avoid over accessing sk_buff.
Reported-by: ChunYu Wang <chunwang@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In release_stripe_plug(), if a stripe_head has its STRIPE_ON_UNPLUG_LIST
set, it indicates that this stripe_head is already in the raid5_plug_cb
list and release_stripe() would be called instead to drop a reference
count. Otherwise, the STRIPE_ON_UNPLUG_LIST bit would be set for this
stripe_head and it will get queued into the raid5_plug_cb list.
Since break_stripe_batch_list() did not preserve STRIPE_ON_UNPLUG_LIST,
A stripe could be re-added to plug list while it is still on that list
in the following situation. If stripe_head A is added to another
stripe_head B's batch list, in this case A will have its
batch_head != NULL and be added into the plug list. After that,
stripe_head B gets handled and called break_stripe_batch_list() to
reset all the batched stripe_head(including A which is still on
the plug list)'s state and reset their batch_head to NULL.
Before the plug list gets processed, if there is another write request
comes in and get stripe_head A, A will have its batch_head == NULL
(cleared by calling break_stripe_batch_list() on B) and be added to
plug list once again.
Signed-off-by: Dennis Yang <dennisyang@qnap.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a race condition in below scenario, say have 3 continuous stripes, sh1,
sh2 and sh3, sh1 is the stripe_head of sh2 and sh3:
CPU1 CPU2 CPU3
handle_stripe(sh3)
stripe_add_to_batch_list(sh3)
-> lock(sh2, sh3)
-> lock batch_lock(sh1)
-> add sh3 to batch_list of sh1
-> unlock batch_lock(sh1)
clear_batch_ready(sh1)
-> lock(sh1) and batch_lock(sh1)
-> clear STRIPE_BATCH_READY for all stripes in batch_list
-> unlock(sh1) and batch_lock(sh1)
->clear_batch_ready(sh3)
-->test_and_clear_bit(STRIPE_BATCH_READY, sh3)
--->return 0 as sh->batch == NULL
-> sh3->batch_head = sh1
-> unlock (sh2, sh3)
In CPU1, handle_stripe will continue handle sh3 even it's in batch stripe list
of sh1. By moving sh3->batch_head assignment in to batch_lock, we make it
impossible to clear STRIPE_BATCH_READY before batch_head is set.
Thanks Stephane for helping debug this tricky issue.
One convenient way to erase trace is "echo > trace". However, this
is currently broken if the current tracer is irqsoff tracer. This
is because irqsoff tracer use max_buffer as the default trace
buffer.
Set the max_buffer as the one to be cleared when it's the trace
buffer currently in use.
Link: http://lkml.kernel.org/r/1505754215-29411-1-git-send-email-byan@nvidia.com Cc: <mingo@redhat.com> Fixes: 4acd4d00f ("tracing: give easy way to clear trace buffer") Signed-off-by: Bo Yan <byan@nvidia.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading data from trace_pipe, tracing_wait_pipe() performs a
check to see if tracing has been turned off after some data was read.
Currently, this check always looks at global trace state, but it
should be checking the trace instance where trace_pipe is located at.
Because of this bug, cat instances/i1/trace_pipe in the following
script will immediately exit instead of waiting for data:
Al Viro pointed out that while one thread of a process is executing
in kvm_vm_ioctl_create_spapr_tce(), another thread could guess the
file descriptor returned by anon_inode_getfd() and close() it before
the first thread has added it to the kvm->arch.spapr_tce_tables list.
That highlights a more general problem: there is no mutual exclusion
between writers to the spapr_tce_tables list, leading to the
possibility of the list becoming corrupted, which could cause a
host kernel crash.
To fix the mutual exclusion problem, we add a mutex_lock/unlock
pair around the list_del_rce in kvm_spapr_tce_release().
If another thread does guess the file descriptor returned by the
anon_inode_getfd() call in kvm_vm_ioctl_create_spapr_tce() and closes
it, its call to kvm_spapr_tce_release() will not do any harm because
it will have to wait until the first thread has released kvm->lock.
The other things that the second thread could do with the guessed
file descriptor are to mmap it or to pass it as a parameter to a
KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE ioctl on a KVM device fd. An mmap
call won't cause any harm because kvm_spapr_tce_mmap() and
kvm_spapr_tce_fault() don't access the spapr_tce_tables list or
the kvmppc_spapr_tce_table.list field, and the fields that they do use
have been properly initialized by the time of the anon_inode_getfd()
call.
The KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE ioctl calls
kvm_spapr_tce_attach_iommu_group(), which scans the spapr_tce_tables
list looking for the kvmppc_spapr_tce_table struct corresponding to
the fd given as the parameter. Either it will find the new entry
or it won't; if it doesn't, it just returns an error, and if it
does, it will function normally. So, in each case there is no
harmful effect.
[paulus@ozlabs.org - moved parts of the upstream patch into the backport
of 47c5310a8dbe, adjusted this commit message accordingly.]
Fixes: 366baf28ee3f ("KVM: PPC: Use RCU for arch.spapr_tce_tables") Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nixiaoming pointed out that there is a memory leak in
kvm_vm_ioctl_create_spapr_tce() if the call to anon_inode_getfd()
fails; the memory allocated for the kvmppc_spapr_tce_table struct
is not freed, and nor are the pages allocated for the iommu
tables. In addition, we have already incremented the process's
count of locked memory pages, and this doesn't get restored on
error.
David Hildenbrand pointed out that there is a race in that the
function checks early on that there is not already an entry in the
stt->iommu_tables list with the same LIOBN, but an entry with the
same LIOBN could get added between then and when the new entry is
added to the list.
This fixes all three problems. To simplify things, we now call
anon_inode_getfd() before placing the new entry in the list. The
check for an existing entry is done while holding the kvm->lock
mutex, immediately before adding the new entry to the list.
Finally, on failure we now call kvmppc_account_memlimit to
decrement the process's count of locked memory pages.
[paulus@ozlabs.org - folded in that part of edd03602d972 ("KVM:
PPC: Book3S HV: Protect updates to spapr_tce_tables list", 2017-08-28)
which restructured the code that 47c5310a8dbe modified, to avoid
a build failure caused by the absence of put_unused_fd().]
Fixes: 54738c097163 ("KVM: PPC: Accelerate H_PUT_TCE by implementing it in real mode") Fixes: f8626985c7c2 ("KVM: PPC: Account TCE-containing pages in locked_vm") Reported-by: Nixiaoming <nixiaoming@huawei.com> Reported-by: David Hildenbrand <david@redhat.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
for_each_active_irq() iterates the sparse irq allocation bitmap. The caller
must hold sparse_irq_lock. Several code pathes expect that an active bit in
the sparse bitmap also has a valid interrupt descriptor.
Unfortunately that's not true. The (de)allocation is a two step process,
which holds the sparse_irq_lock only across the queue/remove from the radix
tree and the set/clear in the allocation bitmap.
If a iteration locks sparse_irq_lock between the two steps, then it might
see an active bit but the corresponding irq descriptor is NULL. If that is
dereferenced unconditionally, then the kernel oopses. Of course, all
iterator sites could be audited and fixed, but....
There is no reason why the sparse_irq_lock needs to be dropped between the
two steps, in fact the code becomes simpler when the mutex is held across
both and the semantics become more straight forward, so future problems of
missing NULL pointer checks in the iteration are avoided and all existing
sites are fixed in one go.
Expand the lock held sections so both operations are covered and the bitmap
and the radixtree are in sync.
Fixes: a05a900a51c7 ("genirq: Make sparse_lock a mutex") Reported-and-tested-by: Huang Ying <ying.huang@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When HW ROC is supported it is possible that after the HW notified
that the ROC has started, the ROC was cancelled and another ROC was
added while the hw_roc_start worker is waiting on the mutex (since
cancelling the ROC and adding another one also holds the same mutex).
As a result, the hw_roc_start worker will continue to run after the
new ROC is added but before it is actually started by the HW.
This may result in notifying userspace that the ROC has started before
it actually does, or in case of management tx ROC, in an attempt to
tx while not on the right channel.
In addition, when the driver will notify mac80211 that the second ROC
has started, mac80211 will warn that this ROC has already been
notified.
Fix this by flushing the hw_roc_start work before cancelling an ROC.
In struct ieee80211_tx_info, control.vif pointer and rate_driver_data[0]
falls on the same place, depending on the union usage.
During the whole TX process, the union is referred to as a control struct,
which holds the vif that is later used in the tx flow, especially in order
to derive the used tx power.
Referring direcly to rate_driver_data[0] and assigning a value to it,
overwrites the vif pointer, hence making all later references irrelevant.
Moreover, rate_driver_data[0] isn't used later in the flow in order to
retrieve the channel that it is pointing to.
Signed-off-by: Beni Lev <beni.lev@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With TXQs, the AP_VLAN interfaces are resolved to their owner AP
interface when enqueuing the frame, which makes sense since the
frame really goes out on that as far as the driver is concerned.
However, this introduces a problem: frames to be encrypted with
a VLAN-specific GTK will now be encrypted with the AP GTK, since
the information about which virtual interface to use to select
the key is taken from the TXQ.
Fix this by preserving info->control.vif and using that in the
dequeue function. This now requires doing the driver-mapping
in the dequeue as well.
Since there's no way to filter the frames that are sitting on a
TXQ, drop all frames, which may affect other interfaces, when an
AP_VLAN is removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0a1eb2d474ed ("fs/proc: Stop reporting eip and esp in
/proc/PID/stat") stopped reporting eip/esp because it is
racy and dangerous for executing tasks. The comment adds:
As far as I know, there are no use programs that make any
material use of these fields, so just get rid of them.
However, existing userspace core-dump-handler applications (for
example, minicoredumper) are using these fields since they
provide an excellent cross-platform interface to these valuable
pointers. So that commit introduced a user space visible
regression.
Partially revert the change and make the readout possible for
tasks with the proper permissions and only if the target task
has the PF_DUMPCORE flag set.
Fixes: 0a1eb2d474ed ("fs/proc: Stop reporting eip and esp in> /proc/PID/stat") Reported-by: Marco Felsch <marco.felsch@preh.de> Signed-off-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Andy Lutomirski <luto@kernel.org> Cc: Tycho Andersen <tycho.andersen@canonical.com> Cc: Kees Cook <keescook@chromium.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Brian Gerst <brgerst@gmail.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Borislav Petkov <bp@alien8.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Linux API <linux-api@vger.kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/87poatfwg6.fsf@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race that cause cifs reconnect in cifs_mount,
- cifs_mount
- cifs_get_tcp_session
- [ start thread cifs_demultiplex_thread
- cifs_read_from_socket: -ECONNABORTED
- DELAY_WORK smb2_reconnect_server ]
- cifs_setup_session
- [ smb2_reconnect_server ]
auth_key.response was allocated in cifs_setup_session, and
will release when the session destoried. So when session re-
connect, auth_key.response should be check and released.
Tested with my system:
CIFS VFS: Free previous auth_key.response = ffff8800320bbf80
Signed-off-by: Shu Wang <shuwang@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shu Wang <shuwang@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most importantly, solve a crash where %llu was used to format signed
numbers. This would cause a buffer overflow when reading sysfs
writeback_rate_debug, as only 20 bytes were allocated for this and
%llu writes 20 characters plus a null.
Always use the units mechanism rather than having different output
paths for simplicity.
Also, correct problems with display output where 1.10 was a larger
number than 1.09, by multiplying by 10 and then dividing by 1024 instead
of dividing by 100. (Remainders of >= 1000 would print as .10).
Minor changes: Always display the decimal point instead of trying to
omit it based on number of digits shown. Decide what units to use
based on 1000 as a threshold, not 1024 (in other words, always print
at most 3 digits before the decimal point).
Signed-off-by: Michael Lyle <mlyle@lyle.org> Reported-by: Dmitry Yu Okunev <dyokunev@ut.mephi.ru> Acked-by: Kent Overstreet <kent.overstreet@gmail.com> Reviewed-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you encounter any errors in bch_cached_dev_attach it will return
a negative error code. The variable 'v' which stores the result is
unsigned, thus user space sees a very large value returned for bytes
written which can cause incorrect user space behavior. Utilize 1
signed variable to use throughout the function to preserve error return
capability.
Signed-off-by: Tony Asleson <tasleson@redhat.com> Acked-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__update_write_rate() uses a Proportion-Differentiation Controller
algorithm to control writeback rate. A dirty target number is used in
this PD controller to control writeback rate. A larger target number
will make the writeback rate smaller, on the versus, a smaller target
number will make the writeback rate larger.
bcache uses the following steps to calculate the target number,
1) cache_sectors = all-buckets-of-cache-set * buckets-size
2) cache_dirty_target = cache_sectors * cached-device-writeback_percent
3) target = cache_dirty_target *
(sectors-of-cached-device/sectors-of-all-cached-devices-of-this-cache-set)
The calculation at step 1) for cache_sectors is incorrect, which does
not consider dirty blocks occupied by flash only volume.
A flash only volume can be took as a bcache device without cached
device. All data sectors allocated for it are persistent on cache device
and marked dirty, they are not touched by bcache writeback and garbage
collection code. So data blocks of flash only volume should be ignore
when calculating cache_sectors of cache set.
Current code does not subtract dirty sectors of flash only volume, which
results a larger target number from the above 3 steps. And in sequence
the cache device's writeback rate is smaller then a correct value,
writeback speed is slower on all cached devices.
This patch fixes the incorrect slower writeback rate by subtracting
dirty sectors of flash only volumes in __update_writeback_rate().
(Commit log composed by Coly Li to pass checkpatch.pl checking)
If blkdev_get_by_path() in register_bcache() fails, we try to lookup the
block device using lookup_bdev() to detect which situation we are in to
properly report error. However we never drop the reference returned to
us from lookup_bdev(). Fix that.
Signed-off-by: Jan Kara <jack@suse.cz> Acked-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcache uses a Proportion-Differentiation Controller algorithm to control
writeback rate to cached devices. In the PD controller algorithm, dirty
stripes of thin flash device should not be counted in, because flash only
volumes never write back dirty data.
Currently dirty stripe counter for thin flash device is not initialized
when the thin flash device starts. Which means the following calculation
in PD controller will reference an undefined dirty stripes number, and
all cached devices attached to the same cache set where the thin flash
device lies on may have an inaccurate writeback rate.
This patch calles bch_sectors_dirty_init() in flash_dev_run(), to
correctly initialize dirty stripe counter when the thin flash device
starts to run. This patch also does following parameter data type change,
-void bch_sectors_dirty_init(struct cached_dev *dc);
+void bch_sectors_dirty_init(struct bcache_device *);
to call this function conveniently in flash_dev_run().
When the devfreq_add_device fails to register deivce, the memory
leak of devfreq instance happen. So, this patch fix the memory
leak issue. Before freeing the devfreq instance checks whether
devfreq instance is NULL or not because the device_unregister()
frees the devfreq instance when jumping to the 'err_init'.
It is to prevent the duplicate the kfee(devfreq).
The size of uvc_control_mapping is user controlled leading to a
potential heap overflow in the uvc driver. This adds a check to verify
the user provided size fits within the bounds of the defined buffer
size.
Originally-from: Richard Simmons <rssimmo@amazon.com>
Certain syscalls like recvmmsg support 64 bit timespec values for the
X32 ABI. The helper function compat_put_timespec converts a timespec
value to a 32 bit or 64 bit value depending on what ABI is used. The
v4l2 compat layer, however, is not designed to support 64 bit timespec
values and always uses 32 bit values. Hence, compat_put_timespec must
not be used.
Without this patch, user space will be provided with bad timestamp
values from the VIDIOC_DQEVENT ioctl. Also, fields of the struct
v4l2_event32 that come immediately after timestamp get overwritten,
namely the field named id.
Fixes: 81993e81a994 ("compat: Get rid of (get|put)_compat_time(val|spec)") Cc: H. Peter Anvin <hpa@linux.intel.com> Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Cc: Tiffany Lin <tiffany.lin@mediatek.com> Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Daniel Mentz <danielmentz@google.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The order in __tlb_flush_mm_lazy is to flush TLB first and then clear
the mm->context.flush_mm bit. This can lead to missed flushes as the
bit can be set anytime, the order needs to be the other way aronud.
But this leads to a different race, __tlb_flush_mm_lazy may be called
on two CPUs concurrently. If mm->context.flush_mm is cleared first then
another CPU can bypass __tlb_flush_mm_lazy although the first CPU has
not done the flush yet. In a virtualized environment the time until the
flush is finally completed can be arbitrarily long.
Add a spinlock to serialize __tlb_flush_mm_lazy and use the function
in finish_arch_post_lock_switch as well.
The local TLB flushing code keeps an additional mask in the mm.context,
the cpu_attach_mask. At the time a global flush of an address space is
done the cpu_attach_mask is copied to the mm_cpumask in order to avoid
future global flushes in case the mm is used by a single CPU only after
the flush.
Trouble is that the reset of the mm_cpumask is racy against the detach
of an mm address space by switch_mm. The current order is first the
global TLB flush and then the copy of the cpu_attach_mask to the
mm_cpumask. The order needs to be the other way around.
projects / linux-4.9.git / log